Yellow DAC Rev 2.1

  • DAC ICs - TDA1387
  • Board size - 100×100 mm
  • PCM - Up to 384kHz / 16-bit (Experimental 768 kHz / 16-bit)
  • Control - MCU STM32F030C8 or stand-alone
  • Power supply - DC 2x15V, DC 6V, DC 9V @ 0.1A
  • Inputs - USB I2S interface
  • Features - Ultra-low-noise power supply, No-Oversampling (NOS) or ADAU1701 options, USB galvanic isolation, power monitoring
  • AUX - ADAU1401 and ADAU1701 on-board support

Multibit TDA1387 DAC - Project Overview

Yellow DAC Rev 2.1 is a compact, no-oversampling (NOS) digital-to-analog converter designed around the classic TDA1387 multibit DAC chips from Philips. In accordance with the DacHobbyLab naming convention, the 'Yellow' designation signifies our focus on legacy vintage multibit architectures, offering a distinctly different, organic sonic signature compared to modern delta-sigma designs.

The board features a parallel dual-chip architecture, versatile digital signal processing expansion via an onboard DSP footprint, and a high-performance ultra-low-noise power regulation stage optimized for high-end DIY audio builds.

Yellow DAC Rev 2.1 assembled board with USB module mounted

Architecture and I/V Stage

At the heart of the Yellow DAC Rev 2.1 are two TDA1387 DAC chips running in parallel. Paralleling the DACs doubles the output current, which improves the signal-to-noise ratio and provides better drive capability for the subsequent current-to-voltage (I/V) conversion stage. In this specific dual-chip implementation, the total quiescent output current fed into the I/V stage is approximately 1 mA at idle, yielding a total dynamic signal swing ranging from 0 to 2 mA.

True to its classic architecture, the Yellow DAC operates natively in No-Oversampling (NOS) mode, avoiding digital interpolation artifacts and delivering a highly transparent, time-perfect transient response favored by multibit enthusiasts. While the official target spec covers PCM up to 384kHz / 16-bit, the hardware layout is capable of handling experimental sample rates up to 768kHz at 16-bit (but not 32-bit), pushing the limits of the TDA1387 interface.

DSP Co-Processor & Inputs

A major hardware feature of this revision is the integrated onboard support for an ADAU1401 (or ADAU1701) DSP module accompanied by a dedicated EEPROM. The layout is highly flexible, allowing the board to process USB I2S signals passing directly from the onboard DSP, or bypass it entirely to read I2S streams directly from a standard stacked USB-I2S card.

Please note: While the hardware layout and the dedicated EEPROM routing are fully implemented on the PCB, there is currently no working stock firmware provided for the ADAU1401 section. It is intended as an open platform for DIY experimentation.

System management, input switching, power monitoring, and OLED interface tasks are reliably driven by the active STM32F030C8T6 microcontroller. Stand-alone control is also available.

Yellow DAC TDA1387 Rev 2.1 schematic

Ultra-Low-Noise Power Supply Architecture

As a Revision 2.x design in the DacHobbyLab ecosystem, this board drops onboard AC rectification in favor of pure, external rectified and pre-regulated DC power. It shares the standard Rev 2.x modular power footprint, requiring clean external DC lines: 6-7V, 8-10V, and +/- 15-17V. To isolate sensitive audio circuitry from digital hash and voltage fluctuations, the PCB is equipped with high-end, dedicated low-noise regulation stages:

  • TPS7A2050: Ultra-low-noise, high-PSR linear regulators handling critical digital and analog TDA1387 line.
  • M5230L: A specialized semiconductor variable voltage regulator driving the operational amplifier rails, renowned in audio engineering for its excellent ripple rejection and exceptionally low noise floor.

The board also features built-in USB galvanic isolation to effectively break ground loops and eliminate incoming EMI/RFI noise from the host PC source.

Listening Impressions

The Yellow DAC Rev 2.1 delivers the classic, sought-after vintage multibit sound: warm, highly musical, and structurally cohesive. The parallel TDA1387 configuration adds a noticeable layer of weight, punch, and authority to the lower mid-range and bass presentation when compared to a single-chip configuration. Thanks to the native NOS architecture and the ultra-quiet power rails enabled by the TPS7A2050 and M5230L, the soundstage remains remarkably dark, allowing micro-details and acoustic space cues to emerge naturally without artificial high-frequency emphasis.

Published on 21 May, 2026Updated on 02 November, 2026