White DAC Rev 2.1

  • DAC Chip - CS4398
  • Dynamic Range / THD+N - 120dB / -107dB
  • Board size - 100×100 mm
  • PCM - up to 192kHz / 24bit
  • DSD - up to DSD256
  • Control - MCU STM32F030C6
  • Power supply - DC 2x15V, DC 6V, DC 9V @ 0.1A
  • Inputs - USB-to-I2S interface, S/PDIF coaxial and optical
  • Features - Selectable digital filter Fast or Slow, USB galvanic isolation, power monitoring
  • Display - SH1106 and SSD1306 I2C 128x64 modules supported

DIY Audio DAC Based on CS4398 - Project Overview

White DAC Rev 2.1 evolves the digital-to-analog converter platform built around Cirrus Logic delta-sigma CS4398 chip with full I2C control. While the previous Rev 1 used direct transformer AC input, Revision 2.x shifts to a compact 100×100 mm modular footprint with external DC power, it features advanced low-noise regulation, expanded connectivity, and galvanic isolation. The project features the CS8416 S/PDIF receiver, offering both coaxial S/PDIF and a Toslink optical input managed via its internal multiplexer controlled over the I2C interface.

White DAC CS4398 Rev 2.1 assembled DAC

Digital Control

An onboard STM32F030C6 microcontroller handles overall system management, reads board configurations and user controls, drives the OLED display, and operates both the CS4398 and CS8416 chips in their native software I2C mode.

It automatically detects the CS8416 S/PDIF receiver at boot and seamlessly switches to a USB-only configuration if it is absent. Utilizes the built-in 8-bit ADC to sample rail voltage and trigger an output mute relay during power-down drops. Auto-detects SSD1306 or SH1106 OLED drivers (128x64) and offers dual software brightness levels. Allows real-time toggling between Fast and Slow digital filter profiles. Features an 3-second Independent Watchdog timer (IWDG) for automated recovery.

MCLK is supplied externally by the CS8416 or USB transport via an LVC157 multiplexer, supporting 512Fs and 1024Fs frequencies via the chip's internal divide-by-2 option.

White DAC CS4398 Rev 2.1 schematic

Upgraded Analog Stage

The analog output stage features a flexible combined SOIC-8 and DIP-8 footprint for op-amp rolling experimentation (such as OPA1612, LM4562, or NE5532). It feeds into a Class-A discrete buffer stage with BC547 transistors and J-FET loads, protected by an MCU-controlled signal relay to eliminate pops during startup or tracks shifts. CS4398 analog sections use dual regulation (LM7806 regulator, C-L-C passive filtering, two TPS7A2050 ultra-low-noise linear regulators). LPF and discrete output buffer are powered via a dedicated M5230L tracking regulator.

Board Power Supply

The board relies on external, clean and preferably stabilized DC rails. Either the Energy Ultra-Prime or the Energy Ultra-Quad linear PSU can be used to provide clean power to the board.

The required DC input lines are distributed as follows:

  • CS4398 Analog Stage: DC 8V to 12V, which next passes through an LM7806 regulator and two TPS7A2050 ultra-low-noise regulators to provide clean +5V VREF and VA voltages.
  • Board Digital Supply: DC 6V to 9V, next routed through an LM1117-3.3 regulator to supply the +3.3V digital lines, external OLED display, galvanic isolation circuitry, and the CS8416 receiver (including its +3.3V analog rail isolated via an LC filter).
  • LPF & Output Buffer: Dual-polar DC ±15V to ±18V, which next feeds into an M5230L regulator to provide a low-noise ±12V supply for the LPF op-amp and discrete output stage.

Voltage Drop Detector

The power-off sensing system relies on a hardware voltage divider connected to the incoming +9VD_NF rail using resistors R30 and R31.

  • PCB Layout: The PCB layout was originally designed to accommodate a dedicated hardware comparator circuit (DD7). However, direct ADC-based monitoring proved to be significantly more reliable, leading to the removal of the comparator stage. To utilize the ADC method, components R30, R31, R40, C55, C59, and the "Direct ADC" 0805 jumper must be populated on the PCB.
  • Hardware Setup: The resistor values (e.g., 10kOhm for R30 and 6.8kOhm for R31) must be selected to step down the rail voltage to approximately 2.0V–3.0V at the MCU analog input pin. In this configuration, R40 is 1kΩ, while C55 and C59 are both 1nF.
  • Firmware Logic: At boot, the MCU checks the V_DETECT analog pin. If a valid voltage is detected, the power-monitoring routine initializes immediately. If a sudden rail voltage drop occurs during operation, the MCU catches it instantly and drops the output relay to ensure a completely click-free shutdown.
  • Bypass Mode: If the ADC pin reads between 0V and 1V at startup (e.g., R30 is missing), the system assumes the detector is disabled. The firmware skips the tracking routine and boots normally, though a minor pop noise may occur upon manual power-down.

Listening Impressions

The CS4398 chip is known for its smooth midrange and natural presentation. The Rev 2.1 maintains the organic tone of the CS4398 while lowering the noise floor and enhancing clarity, providing an airy and non-fatiguing presentation for extended listening sessions.

Published on 21 May, 2026Updated on 09 November, 2026